Millworker Help
Millworker is an Autodesk Inventor 2026 and 2027 add-in for millwork and cabinet panels: joins, fasteners, machining features, door and panel treatments, materials, hardware, drawings and reports, all on one Millworker ribbon tab. Every tool works on solid bodies in a multi-body part (or on the parts of an assembly), shows a preview before it changes anything, and drives everything it makes from parameters.
New to Millworker? Start with Getting started, then How the tools work. Pick a tool below or use Find a tool at the top. There is also a printable version of the whole guide.
Getting started
Getting startedWhat Millworker is, what it needs, and a first joint in five minutes.Install and updateInstall Millworker, switch it on in Inventor, and where its files are kept.
Licence, trial and buyingThe 7-day trial, buying Millworker and its add-ons, signing in on another computer, and moving a licence.The Millworker ribbonWhich panels show in parts, assemblies and drawings, and what each tool is for.How the tools workMini toolbars, picks, see-through previews, Apply and OK, and the Millworker node each tool makes.Editing a Millworker nodeDouble-click a node to open its tool again with its picks and values, change them, and remake it in place.Tool unitsShow every tool size in inches or millimetres.Parameters and MW_ namesEvery size a tool makes is a user parameter in the part's Millworker group, so changes follow through.Settings
Panel Marking
Joins
Dado JoinCut a dado in the master panel and run the panels into it, however they sit: overlapping, touching or short of it.
Miter JoinMiter two panels at their corner, with a gap, and mark the miters for the nest.
HalvingHalve two crossing bodies into each other, with clearance and CAM corners, and keep it parametric.
Corner QuirkTurn a butt corner into a dado or locking quirk joint, with a 1/8 or 1/4 in quirk.
TonguePut a centred tongue along board edges, with corners that meet cleanly.
GrooveCut a centred groove along board edges, run out at both ends, sized for the mating tongue plus clearance.Fasteners
DowelsDrill System 32 dowel pairs in butt joints, laid out from the cabinet side's front edge.
Cam DowelsBore cam fittings and their dowels in pairs on the System 32 layout.
ConfirmatConfirmat (joint screw) holes in a butt joint, from a hole type with an edge pilot: through the side with its head, a pilot into the butting panel's end.
Place HoleHoles of a hole type in a panel, on a sketch's points or measured from two edges, previewed as they will be cut.
Hole TypesYour own list of holes: their sizes in mm, a cross-section of each, and the fastener that goes in it.
DominoDomino mortises in the side's face and the butting panel's end, for the tenon size you choose.
Biscuit#0, #10 or #20 biscuit slots cut as a 100 mm blade cuts them.
Clamex PClamex P connector slots in the side's face and the butting panel's end.
Pocket ScrewsAngled pocket holes in the butting panel, coming out of its end into the side.
Dog BoneDog bone pockets for countertop and subtop clamps, across a joint, spread from front to back.Features
Bubble BaseMake a bubble base to drive your base model. Create your panels on the bubble for easy model control.
Panel MakerClick faces and make each one a separate panel body of a set thickness.
Dado EdgeA rabbet (edge dado) along panel edges, Width in from the edge and Depth into the face.
Stop ShoulderStop a dado short of the panel end, and notch the part running in it to suit.
Edge InsetSet panel edges back by a small inset, for reveals or edgebanding allowance.
CAM CornersDog-ear the square inside corners a round CNC cutter cannot reach, so square parts fit.
Hinge HolesBore concealed (35 mm cup) hinge holes in a door, and the plate holes in the cabinet side.
Shelf HolesDrill rows of 5 mm shelf pin holes up a cabinet side, on a 32 mm pitch from a shelf.
LED ChannelGrooves for LED tape along a face's edges, joining cleanly at corners.
Edge ProfileRound-over, chamfer, cove, ogee and your own profiles along edges, with a profile editor.Treatment
Shaker DoorSplit a door slab into a 5-piece shaker door: stiles, rails with stub tenons, and a floating panel.
LatticeTurn a body into slats, or groove and flute it, with a width and spacing that follow its length.
SunburstTurn a body into slats set out along curves (an arc, or a seat's profile curving either way), the same width all the way, the gaps tapering.
Split OutMake each separate lump of a body into a body of its own.
Copy BodyCopy bodies a distance along X, Y or Z, along an edge at an angle, or along a curve, as many times as you need, kept editable.
Waste EnvelopeA sized oversize box round each body for rough stock, shown in yellow and listed on the cut list.
Make FlatFlatten curved wood panels: see the panel and its proposed flat side by side, sized from the panel, and save it as its wood flat.Materials
Material ManagerThe shop's materials, edgebands, veneers and finishes in one shared database: a manager only.
Materials FinishesAssign a material or finish to parts from a mini toolbar, without opening the manager.
Part NumbersNumber every part in the assembly from project, item, room and a running ID.
Cut ListEvery panel in the assembly with cut sizes, material, banding, miters and dados, to print or save.
BOMBill of materials: sheet goods to buy, panels, layups, hardware, finish areas and edgebanding lengths.
Quick TakeoffThe sheets, layups, hardware and edgebanding to buy, counted from the assembly, as a report.
Material GroupsA quick check of the assembly's materials: each material in a colour, its parts lit in that colour while the window is open.
Bodies to PartEvery body in the assembly into one new part, each a separate body with its appearance.
Push to MatFinSet up the project's references in its MatFin workbook: the assembly's materials come in to match to INNERGY, rows are changed, layups made, then one Save.
Tag LayupsPut the project's layups on parts with a mini toolbar: choose the layup, click the panels, Apply.Hardware
Tools
Parameters side barThe active document's parameters at a glance in a docked window, with a copy button for each name.
Parameter ManagerEvery parameter with every column, groups, lists, tolerances, checking as you type, and more.
Functions and formulasIF/THEN formulas and your own functions on parameters, worked out by Millworker.
CreateMake a new drawing, part, base model, assembly, cabinet, curved panel or sheet metal part in its project and work order folder, with the project's info on it.
Project InfoThe project's details and part numbers in its MatFin workbook, and the iProperties pushed down to every subassembly and part.
Design CopyA new, renamed version of an assembly (or a drawing and its assembly) with everything it uses, in another folder: Copy or Reuse each file, rename them all at once from the ribbon, set iProperties.Reference
Drawings
CalloutsClick an edge in a view: a boxed note with its material, finish, coating, edgeband or veneer code, left or right of the view, that follows the part.
Align lines and reference boxesRed dashed lines to line leaders and text up on, and boxes round views, on a layer that never prints.
Section LineA section view with architectural heads and tails: a bubble with the section and sheet, and an arrow the way it looks.
Update LabelsRe-letter every section and detail from sheet 1, and name views FRONT VIEW, SIDE VIEW, PLAN VIEW.
Reset LabelsPut every view label on the sheet back to its style's own text.
Grey SectionsEvery section hatch on the sheet solid light grey.
Copy SheetsCopy sheets with a different model on each copy; the originals stay as they are.
Drawing BuilderA full drawing set from an assembly: one sheet per model, laid out by your sheet layouts.
Sheet NamesRename every sheet from the model on it: description, part number, job number.
Sheet TableA sheet index (number and title of every sheet) that keeps itself up to date.
Reference TablesThe project's MatFin workbook as front page tables: general notes, client refs, finishes, materials, layups, hardware.
Sheet RefsWrite each model's sheet numbers into its MillworkerSheetRef iProperty, for parts lists.
Update MassiProperties, Physical, Update for every part and assembly: quick, or rebuild and save.
Drawing OutputExport PDF, DWG, DXF, BOM, STEP and USDZ from one drawing or every open drawing, named and filed by a profile.
Show and Clear Mark TypesDoors' and drawers' opening lines and hinge holes, drawn from the parts marked with Cabinet Marker.
AutoDimDimension a cabinet view's doors and drawer fronts, or one panel, the shop's way.
Show FlatPlace the flat of a curved panel (Make Flat) or a sheet metal part from the models on this sheet.