Inventor Add-insby Shaw Development

Add-on for Millworker · Inventor 2026 and 2027

CabinetCAD

Three configurators on the Millworker tab: Cabinets, Diewalls and Drawer Box. Type the sizes, see the item in 3D with its drawings and cut list, then send it to Inventor as machine-ready parts and assemblies with every join, hole, edgeband and grain mark already on, ready for NestCAM or Cut List.

Runs on top of Millworker in Autodesk Inventor 2026 and 2027. Built to AWS (Economy, Custom, Premium) or UK BS EN 942 standards, in inches or millimetres.

Cabinets

A whole kitchen or casework layout in one 3D scene.

  • Base, sink base, drawer base, wall, tall, open, blind corner, gable end, gap and counter
  • Overlay, inset or face-framed, changed for the whole layout at once
  • Dadoed, or dowels and cams (Minifix, Maxifix) on the 32 mm system
  • Corner runs turn by themselves; counters follow the cabinets, with dogbones at joints
  • Fill a wall: wall length, number of cabinets, scribes and fillers worked out for you
  • Shelf pin and hinge holes, drawers on the slides you stock
CabinetCAD Cabinets: a layout in 3D.
Screenshotimg/shots/cabinetcad-cabinets.png1600 × 1000 pxCabinetCAD Cabinets window: an L-shaped kitchen run with base and wall cabinets and a counter in 3D, the properties grid on the right, the side profile under it.
CabinetCAD Cabinets: a layout in 3D.

Diewalls

A wall profile run along a sketched line: reception desks, partitions and feature walls.

  • Sketch the line in plan, with straight walls, true arcs and mitred corners
  • Straight joins get matching end plates and bolt holes; corners butt into a corner plate
  • Curved skins in bending ply layers, kerfed sheet or one bending sheet
  • Ribs, plates, subtop, countertop and base plates built for you
  • ADA lower stretches marked on the plan, with finished ends
  • Round, square and slot cable holes through every rib
  • X-ray to see the frame inside the skins
CabinetCAD Diewalls: a curved desk with an ADA stretch.
Screenshotimg/shots/cabinetcad-diewalls.png1600 × 1000 pxCabinetCAD Diewalls window: a curved reception desk with an ADA lower stretch in 3D, X-ray on so the ribs show, the Profile tab with cable holes on the right.
CabinetCAD Diewalls: a curved desk with an ADA stretch.

Drawer Box

The right drawer box for the slide, from the opening width.

  • Blum TANDEM, BLUMOTION and TANDEMBOX, Accuride 3832, Grass Dynapro, Hettich Quadro, Metabox and more
  • Only each system's real slide lengths and heights
  • Wood boxes, or the base and back for metal-sided systems
  • Undermount rear notches and locking device holes
  • Slides and sides sent to Inventor as Purchased parts with their order codes
CabinetCAD Drawer Box.
Screenshotimg/shots/cabinetcad-drawerbox.png1600 × 1000 pxCabinetCAD Drawer Box window: an undermount or TANDEMBOX drawer standing in the see-through cabinet section, the system and length buttons top left, the parts table below.
CabinetCAD Drawer Box.

Your standard, every time

Each list is built to a standard, in inches or millimetres. Your shop's own values sit on top of the standard, and any one cabinet can be changed on its own.

StandardAWS (Economy, Custom, Premium) or UK BS EN 942, then your shop, then the item
StylesOverlay, inset (door faces flush with the sides) and framed
ConstructionDados, shelf pins and setbacks from your shop values, for example dados 1/4″ deep stopped short of the banded front
MaterialsFrom the Inventor libraries or Millworker's material and finish database
Shop values on top of the standard.
Screenshotimg/shots/cabinetcad-settings.png1200 × 800 pxCabinetCAD Settings window with the standard (AWS), units (inches) and the shop values showing.
Shop values on top of the standard.
The finished assembly, already marked.
Screenshotimg/shots/cabinetcad-assembly.png1200 × 800 pxThe Inventor assembly CabinetCAD made from the layout: cabinets with Millworker nodes in the browser, banding and grain marks showing (Show Marks).
The finished assembly, already marked.

Ready for the shop floor

CabinetCAD writes real Inventor parts and assemblies with Millworker's joins, holes, banding and grain marks. Send them straight on to NestCAM or Cut List, or change any panel with Millworker's tools.

M

CabinetCAD needs Millworker

The cabinets it builds are Millworker panels, joins and materials, and its panel sits on the Millworker ribbon tab. Each CabinetCAD seat needs a Millworker licence on the same seat. About Millworker · Pricing